• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Planar Magnetic Speakers

Planar magnetic speakers convert electrical signals to sound using flat diaphragms. They are known for their accuracy and detail, as well as low distortion. They are able to handle a wide spectrum of frequencies, making them easy to hear.

Dynamic drivers feature larger and more rigid diaphragms than thin and ultra-light ones used in planar magnetic speakers. This hinders their ability to accelerate and move quickly, leading to sonic distortion.

They are easy to build

Many people believe that making planar magnetic speakers is a difficult task, but they are extremely easy to build. The key is to follow the steps and construct a well-engineered speaker. The result will be a high-quality audio system that can compete with any available model. Planar magnetic speakers are easy to construct and provide superior sound quality compared to traditional dynamic drivers. They offer superior detail as well as a larger dynamic range and controlled direction that all contribute to an experience that is more immersive.

Unlike conventional loudspeakers, which project sound in circular wave fronts, planar magnetic speakers emit flat waves that are directed. This gives them the ability to reproduce sounds at very low frequencies, which can be difficult for traditional speakers to do. In addition, their incredibly precise imaging can bring music to life in a way that makes standard speakers sound slow in comparison.

A planar magnetic drive generates a sound by using a thin sheet of metal suspended between two conductive plates. The audio signal sends an electrical current to the panel, which rapidly shifts between negatives and positives. The negative portion of the panel is dragged towards the array of magnetics, which moves it forward and back to create a vibration on the diaphragm. The result is a great dynamic response, and a broad soundfield, with no distortion.

One of the most crucial aspects of a planar magnetic speaker's performance is its maximum excursion, or how far the speaker can move before it starts to distort. This is measured at a certain frequency and output level. For instance, if are looking to hear a 20-Hz bass note, then you'll require a speaker that has an excursion of around 1 millimeter.

A reliable planar magnetic driver should be able to withstand high excursion while maintaining its structural integrity. It must be able to disperse heat effectively and handle a large amount of power. To meet these requirements, the voice coil of a speaker must be of sufficient thickness and diameter. Additionally the voice coil should be wrapped with a conductive material that can conduct electricity.

They effectively disperse heat.

This is a very important aspect of any speaker. The voicecoil is very close to the magnet array, and has an extremely high flux density within the gap. Heat is generated by the voicecoil and must be dissipated to avoid distortion and damage. Convection and radiation are two ways in which the voicecoil is able to get rid of heat. Radiation is the preferred method as it doesn't have the pumping effect of the cone's movement, however, it should be done carefully and the design must be capable of handling the power that is being applied.

The first step is to make sure that the gap between the voicecoil and the array is at a minimum of 1 millimeter. This is vital, because the gap could cause very unpleasant distortion if larger than this. The gap must be large enough to allow the voicecoil to move freely without hitting the rear plate. For this reason, the wide gap designs favoured by a variety of manufacturers are not efficient and only work at low frequencies.

A good way to test the gap is to put a magnet on the gap and determine the resistance between the magnet and the voicecoil. The higher the resistance, the less heat is dissipated and the more likely it will distort. The lower the resistance the more efficient the speaker will be, and the less distortion it will cause.

Planar magnetic speakers can reproduce the upper octaves with amazing precision, however they can't replicate the lower frequencies since they require a large diaphragm. That's why many planar magnetic speakers use a woofer and tweeter in combination. This allows them cover an extended frequency range while causing less distortion.

Planar magnetic drivers are well-known for their low distortion and great bass. The dipole design means that they emit equal amounts of energy in both directions and have an inverted phase. This is a significant advantage over traditional drivers that can be subjected to mechanical distortion and strong Q resonances.

They can handle a huge amount of power

Many people are concerned that planar magnetic speakers will not be capable of handling the amount of power that they need, but the truth is that they do. The "voice coil" has a greater surface area than a dynamic driver and can therefore dissipate more heat. The diaphragm is thin and light, also helps to reduce distortion.

It is important to keep in mind that a planar magnetic speaker will require lots of power to create a good sound. They can't easily disperse energy like a traditional speaker, which means they can be sensitive to how the room is set up. They are also directional which means that if you listen from a few degrees away, the sound level can be significantly reduced.

Inefficiency is another factor that makes them able to handle a large amount of power. This is because they have less impedance than standard drivers, which means they require more power to achieve the same listening volume. They also are susceptible to magnetic saturation that can cause distortion.

Measuring the maximum excursion of the planar magnet speaker is an excellent way to determine its ability to handle high-power. This is the length the diaphragm will travel before it hits the magnet array and starts to distort. The most effective planar magnetic speakers will reach a distance of about 1 millimeters before this happens.

Planar magnetic speakers also offer a greater frequency range than cone drivers. This is beneficial in certain situations. They can reproduce a higher number of frequencies, which can improve the quality of sound effects and music. This can help to make it easier to distinguish between various instruments and vocals in a song.

The top planar magnetic speakers can reproduce a wide spectrum of frequencies, including the bass frequencies. This can be a huge advantage for those who want to enjoy music in a variety environments. These speakers are more expensive than traditional loudspeakers but offer a distinct, immersive experience. These speakers are also great for home theater systems.

The direction of the arrow is crucial.

When an electrical signal is positioned to the conductive trace patterns the magnetic field causes the diaphragm to move, which creates sound waves. The movement is much more precise and controlled compared to traditional cone drivers, which allows for a larger frequency response. This allows planar speakers reproduce more clarity and detail in the music.

These flat diaphragms are available in two distinct designs such as dipole (radiating in both directions, like electrostatics and Maggies) or monopole (radiating in only one direction, similar to traditional dynamic speakers). This flexibility provides designers with a wide range of options for Headphone Planar Magnetic wall or in-wall loudspeakers which can deliver exceptional performance at affordable costs.

The diaphragm inside a planar magnetic driver is generally constructed from an ultra-thin, light polymer that is coated with a copper circuit which conducts electricity. The diaphragm that is coated with metal is surrounded by an array of magnets that are arranged in bars with a wide spacing. These magnets create a powerful magnetic field that can draw and disperse the diaphragm's air particles. The magnetic fields help radiate heat away from speaker without straining the voice coil.

Planar magnetic speakers have a greater sensitivities than cone speakers that are conventional, and they can handle a large amount of power without overheating. They also have a lower impedance, which means they require less amplification in order to achieve the same levels of listening. They can reproduce a broad spectrum of audio frequencies, including bass and highs. They are usually enhanced by subwoofers with boxed enclosures, which are able to reproduce low-frequency sound with greater precision.

A disadvantage of single-ended planar magnetic loudspeakers is their poor damping. This can result in high-Q resonances within the low frequency spectrum of the speaker's response, which can color the sound. The solution is a hybrid design, that combines the benefits of dipole and planar technologies.

Proper placement of a headphone planar magnetic magnet speaker in the room is among the most crucial elements that determine its success. A variety of aspects of sound are affected by this, including the bass response, imaging and soundstage depth and width. Toe-in is a negative influence on the midrange and the higher frequencies. The speaker should ideally be placed where the central image is narrowest.